NTK Cutting Tools

Hartmetall 〈 55 Grad rhombische positive Platten 〉 55° 7° Ｒ Ｔ IC ● ● ● ● ● ● ● ● ◦ ● ● ● ● ● ● ● ◦ ● ◦ ◦ ◦ ● ◦ ● ◦ ● ● ◦ ● ◦ ● AM3 DCGT 070200 FNAM3 0.03 ● ● ● ● 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 G25 G27 070201 FNAM3 0.1 ● ● 070202 FNAM3 0.2 ● ● 070204 FNAM3 0.4 ● ● 070201M FNAM3 *0.08 ● ● ● ● 070202M FNAM3 *0.18 ● ● ● ● 070204M FNAM3 *0.38 ● ● ● ● DCGT 11T300 FNAM3 0.03 ● ● ● ● 11T302 FNAM3 0.2 ● ● ● 11T304 FNAM3 0.4 ● ● ● 11T301M FNAM3 *0.08 ● ● ● ● ● ● 11T302M FNAM3 *0.18 ● ● ● ● ● ● 11T304M FNAM3 *0.38 ● ● ● ● ● ● DCMT 070202 FNAM3 0.2 ● 070204 FNAM3 0.4 ● DCMT 11T302 FNAM3 0.2 ● 11T304 FNAM3 0.4 ● 11T308 FNAM3 0.8 ● AMX DCGT 070201M AMX *0.08 ● ● ● 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 070202M AMX *0.18 ● ● ● 070204M AMX *0.38 ● ● ● DCGT 11T301M AMX *0.08 ● ● ● 11T302M AMX *0.18 ● ● ● 11T304M AMX *0.38 ● ● ● AZ7  DCGT 070200 AZ7 0.03 ● 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 G25 G27 070201M AZ7 *0.08 ● 070202M AZ7 *0.18 ● DCGT 11T300 AZ7 0.03 ● ● ● ● 11T301M AZ7 *0.08 ● ● ● ● 11T302M AZ7 *0.18 ● ● ● ● 11T304M AZ7 *0.38 ● ● ● ● 11T308 AZ7 0.8 ● ● ● AZ8 DCMT 070202 ENAAZ8 0.2 ● 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 070204 ENBAZ8 0.4 ● 070208 ENBAZ8 0.8 ● DCMT 11T302 ENAAZ8 0.2 ● 11T304 ENBAZ8 0.4 ● 11T308 ENBAZ8 0.8 ● AT DCET 11T301M AT *0.08 R 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 11T302M AT *0.18 R KHG DCET 0702005 KHG 0.05 ● 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 0702008 KHG 0.08 ● 0702018 KHG 0.18 ● 070202 KHG 0.2 ● DCET 11T3005 KHG 0.05 ● R 11T3008 KHG 0.08 ● R 11T3018 KHG 0.18 ● R 11T302 KHG 0.2 ● R UHG Rechte Ansicht DCET 0702008 UHG 0.08 R 0.4 0.2 0.1 0.1 0.3 0.5 1.0 3.0 5.0 0.05 DCET 11T3008 UHG 0.08 R Bezeichnung IC Dicke Winkel DC_0702 6.35 2.38 7° DC_11T3 9.525 3.97 7° E42 Ｅ Positive Platten D Kohlenstoff/Leg.Stahl Edelstahl/Stahlguss Grau / Sphäroguss Aluminium/NE-Metall Nickel-Basis Leg. Gehärtete Materialien Hartmetall ●： Standard-Artikel ● ： Neue Artikel ■： Auf Anfrage 　　★： Festgelegte Ausführung Form ISO-Bezeichnung Inch-Bezeichnung R Hartmetall Spankontrolle PVD-Beschichtet CVD-Besch. ST4 ZM3 QM3 VM1 TM4 DT4 DM4 CP1 CP7 KM1 Werkzeug- halter Siehe Seite: ● ： Empfehlung ◦ ： Alternative Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Schnitttiefe ( ㎜ ) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) Vorschub ( ㎜ /rev) * Wendeschneidplatten mit der Radiusbezeichnung 01 02M oder 04M sind im Radius um 0.02mm kleiner geschliffen um bei Bedarf in der Werkstückzeichnung diese Radien auszufahren.